Based on this YouTube video's total view count of 265K views and industry-standard rates, the estimated total earning is $186 - $530 through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.

Explore How to make Collapsible Display Shelves // Woodworking & Metalworking | I Like To Make Stuff with 265,056 views, 7,137 likes, and 323 comments. Experience the impact of this video content that has captured audience attention.

My friend Alex needed some collapsible shelves to display her goods at craft shows. Come see how we made her a set of display shelves. ALEX'S WOVEN GOODS http://daughterhandwovens.com/ TOOLS & SUPPLIES (affiliate links): https://kit.co/iliketomakestuff/my-metalworking-tools https://kit.co/iliketomakestuff/my-woodworking-tools https://kit.co/iliketomakestuff/shop-safety-gear Blackening Solution: https://www.amazon.com/dp/B06XGQ5WVV?tag=ilik-20 MUSIC: http://share.epidemicsound.com/iltms Just like any product you may make for a client, you need to start with a problem statement from the customer. In her case, Alex needed a unique and eye-catching way to display her woven goods; scarves, table runners, blankets. She needed a combination of flat surfaces and hanging rods so that customers can properly see her work. Most importantly, she needed this shelving setup to be collapsible and transportable. Because she is constantly at craft fairs, she needed to be able to pack up the display in her car, set it up, and break it down all on her own. We decided on a simplistic and industrial look to the shelves. Alex also didn't want the horizontal bracing or support cables on the back of most minimalistic shelving units. She thought this would take away from her hanging products and make the space seem too cluttered. With all of these ideas and constraints in hand, I made a 3d model of my initial concept. After a few small iterations, we got to work making a shelving unit that would be made of two sets of steel side frames with some brackets spaced evenly. These brackets could hold shelves or hanging rods in a number of configurations. The two units could also be used independently or stacked on top of each other using some 3d printed connectors. I chose to use some 3/4" steel square tubing for the shelf frames welded together with some simple butt joints. The welds were cleaned up and the whole frame was sanded down in preparation for finishing. Alex wanted the steel tubing to be black, and I figured that spray paint would eventually rub off, so I used some chemical blackening solution. This is a brush-on liquid that reacts with the steel and turns it black. I've seen a lot of makers have success with this method, but mine turned out rusty-looking and inconsistent. Overall, Alex was happy with the industrial look, but it was far from the blackened finish I was expecting. In order to hold the different combination of shelving ideas, Josh and I came up with a universal mounting bracket. This U-shaped steel bracket would be welded to the frames and hold the ends of the shelves or the hanging rods. Small problem is, I couldn't find a 3/4" steel bracket...so, surprise-surprise, I made some. These brackets began with some left-over 3/4" steel tubing from the frames. I drilled some evenly-spaced holes straight through and used my metal cutting bandsaw to trim off one edge. The square pipe became a long piece of steel C-channel. I then cut this length of channel into smaller pieces and welded them onto the display frames. The hole is for a bolt that will go through the bracket and the shelves to lock the whole unit together. This lateral strength will replace the need for horizontal bracing. Because this display unit is meant to be modular and change with Alex's needs, I am making a combination of flat shelves and rounded hanging rods. She loved the look of walnut and steel, so Josh and I milled up some lumber and got to work. If you are interested in our milling and squaring process, check out the Bits video we made on the subject! I used biscuits to align the walnut boards and glued them together. While those were drying, I cut some thinner pieces and passed the edges through a round-over bit on my router. This created a sturdy hanging rod with nice gentle sides. To get the shelves to fit inside the custom brackets, I used my dado stack to add some rabbets to both ends. I also drilled some slightly over-sized holes that would align with the bracket holes. This uniform method will allow Alex to mix and match shelf pieces as she needed. I applied some polyurethane for protection, and the shelves were done. Subscribe: http://bit.ly/ILikeToMakestuffSubscribe Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos Learn 3d modeling, get digital plans, and cool merch at https://iliketomakestuff.com Want to support ILTMS? Get exclusive content and more... http://www.iliketomakestuff.com/patreon FOLLOW: http://instagram.com/iliketomakestuff http://twitter.com/iliketomakestuff http://facebook.com/iltms About I Like To Make Stuff: We have lots of projects including woodworking, metalworking, electronics, 3D printing, prop making and more! These videos are our attempt inspire and empower others to make the stuff that they want to have. Hopefully you'll see something here that will inspire you to make something that you're passionate about! I Like To Make Stuff http://www.youtube.com/Iliketomakestuff

With SocialCounts.org’s view counter, track your YouTube video’s live view count and YouTube likes count in real time with fast, reliable updates.

Watch every YouTube video live view count rise with our real-time YouTube views tracker—built for accuracy and minimal delay.

Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.

Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.org’s smart tracking tools.