Based on this YouTube video's total view count of 508K views and industry-standard rates, the estimated total earning is $356 - $1.01K through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.

Explore Floating Coat Rack (with cubby) // How-To | I Like To Make Stuff with 508,275 views, 9,253 likes, and 246 comments. Experience the impact of this video content that has captured audience attention.

I made a floating coat rack/cubby using a french cleat, from baltic birch plywood. Here's what you'll need: (purchasing via these affiliate links supports ILTMS) Brass coat hangers - http://amzn.to/1MMT7ZN Wood glue - http://amzn.to/1emnni1 Table Saw - http://amzn.to/1LClPPY Miter Saw - http://amzn.to/1MMV48t Polycrylic (satin finish) - http://amzn.to/1Ieev61 The back panel was a 10" tall piece of 3/4" birch plywood. I cut down three pieces at 5" wide for the shelf section. Using those pieces as a guide, I set a stop block. Then I cut two matching width pieces for the end caps of the cubby. Then I set a stop block to cut off 1 1/2" from the piece that would become the back panel. This is to help it fit inside the cubby. I dry fit the pieces in place to test. I marked along the bottom of the cubby so I wouldn't cut below that line. Then I cut out a large section that was behind the cubby. I set my table saw blade to 45 degrees. Then, using the cutout from above, I split it approximately in half. One of these pieces got trimmed down to 20" long, to become the wall cleat. The shorter length is to allow the shelf to slide back and forth on it. I dry fit everything again and marked all joints with a line for adding biscuits. I also set the remaining cleat on the underside of the top panel, and marked for biscuits. Using a biscuit jointer, I added slots on all necessary pieces. Marking all of the pieces ahead help make sure the biscuit slots line up. I added glue to all of the slots and joint faces, then added biscuits into the slots. All of the biscuit jointed panels were clamped together to dry. The angle on the cleat made it hard to clamp, so I just glued it in place. For biscuit jointing, you just have to line of the mark that you made, which should cross the joint. The now cut out back panel got glued and screwed onto the back of the box. With it flipped over, I added glue to the inside back surfaces. Then I pushed in the back panel as far in as it would go. I added some deep throat clamps to force the panel against the back to dry. Using blue tape, I masked off the bottom front panel. Also, I masked off the front faces of the cubby, trimming it to the edge with a sharp knife. Using a 7 oz. color sample, I painted the front facing panel. I also painted the inside of the cubby, covering all of it with two coats. After it dried, I removed the tape and scraped away any paint that seeped under the tape, with a utility knife. I covered the entire piece with two coats of PolyCrylic. On the front panel, I marked the center point, then the center point of each end (splitting the face into quarters). Then I laid out the coat hangers centered on my marks. I predrilled the two holes on each hanger, so the screw wouldn't drift when being screwed in. Then all three hooks were screwed in place. I predrilled three holes in the wall cleat, one in the center, two at 8" from the center mark. I screwed the cleat to the wall via the center hole, then leveled the cleat. Holding it level, I added the two remaining screws. Finally the shelf was hung onto the cleat, and adjusted laterally for placement. Subscribe: http://bit.ly/ILikeToMakestuffSubscribe Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos Learn 3d modeling, get digital plans, and cool merch at https://iliketomakestuff.com Want to support ILTMS? Get exclusive content and more... http://www.iliketomakestuff.com/patreon FOLLOW: http://instagram.com/iliketomakestuff http://twitter.com/iliketomakestuff http://facebook.com/iltms #ILikeToMakeStuff About I Like To Make Stuff: We have lots of projects including woodworking, metalworking, electronics, 3D printing, prop making and more! These videos are our attempt inspire and empower others to make the stuff that they want to have. Hopefully you'll see something here that will inspire you to make something that you're passionate about! Floating Coat Rack (with cubby) // How-To | I Like To Make Stuff https://www.youtube.com/watch?v=FBLgnytHSYo I Like To Make Stuff http://www.youtube.com/Iliketomakestuff

With SocialCounts.org’s view counter, track your YouTube video’s live view count and YouTube likes count in real time with fast, reliable updates.

Watch every YouTube video live view count rise with our real-time YouTube views tracker—built for accuracy and minimal delay.

Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.

Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.org’s smart tracking tools.