Based on this YouTube video's total view count of 326K views and industry-standard rates, the estimated total earning is $228 - $652 through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.

Explore How to Make a Multi Guitar Stand | I Like To Make Stuff with 326,055 views, 8,885 likes, and 439 comments. Experience the impact of this video content that has captured audience attention.

As many of you know, I have a lot of instruments. Lately, I've been practicing a lot more and needed a place to store all of my guitars. Instead of buying a cheap one, I made a multi guitar stand for all of my amazing instruments, and you can too! There's digital plans listed below! DIGITAL PLANS: https://iliketomakestuff.com/shop/product/multi-guitar-stand-digital-plans/ TOOLS & SUPPLIES WE USED(affiliate links): https://kit.co/iliketomakestuff/my-woodworking-tools https://kit.co/iliketomakestuff/shop-safety-gear MUSIC: http://share.epidemicsound.com/iltms For this multi guitar rack, I wanted to make the structure out of a really nice cherry wood. I had a big block of it from an old project, so I needed to mill it down to size first. We have a BITS video all about milling lumber where Josh went through the process of using the jointer, the planer, and the table saw to get really nice, square pieces of wood. I followed that process and made some square lengths of cherry that will be cut at a 75 degree angle to make up the side structure. The overall shape of the sides will look like an invert lower-case letter "y." I used my digital protractor to transfer a 75 degree line to the wooden pieces and cut those angles on the miter saw. You could simply glue these pieces together using a butt joint and screws, but I wanted to challenge myself by making angled, half-lap joints. A half-lap joint is made by removing half of the material thickness and overlapping another piece with the same amount removed. There are many methods of accomplishing this angled joint, like a vertical jig on the table saw, but I decided to use the bandsaw and a hand saw. With each joint cut, I gathered the other components to assemble and started drilling the holes for the crossmembers and the mounting hardware. With the side structures now prepped and glued together, it was time to assemble the bottom crossmembers and the top holder bar. To connect the bottoms, I wanted to use some leftover 1-1/4" poplar dowel. I glued the two lengths of dowel into the holes I drill in the side structures. For the top bar, I found some 30mm aluminum extrusion left over from the Roof Rack project. This would work really well because I could slide the guitar neck holders around to make room for more instruments. Before I mounted the top bar, I made sure to slide in the extrusion t-nuts into the channels because I wouldn't be able to once it was attached. Then, using some button-head hardware, I attached both sides of the extrusion to the upper side structures and the multi guitar rack was assembled. I then added some rubber feet to the bottom so that it sat up off the ground, making room for the guitars' strap nut. Now it's time to make the guitar neck holders! Now that the multi guitar stand's structure was completed, it was time to make the individual holders for each guitar neck. I used the same cherry wood and drew out an easily repeatable template. Using a forsner bit and the bandsaw, I cut out some U-shaped holders with a mounting hole in the middle. I was told in a previous video that foam, over time, could mess up the finish on guitar necks. To combat this problem, I decided to line the inside of each holder with a strip of dyed leather. This provides some padding and protection to each guitar neck. After some simple beeswax finish, I used some 1/4"-20 screws to attach each holder to the extrusion's t-nuts. I moved the rack into the studio and loaded up the multi guitar rack with all of my instruments. Using the extrusion allowed me to space the neck holders to fit each instrument, allowing me to fit more guitars on the rack. Right now, I have an acoustic guitar, a bass, and four electric guitars on the rack with room to spare! I am really happy with this design, but I plan on updating some simple things in the future. First, I want to add taller feet to make room for some longer strap nuts. Secondly, I want to wrap the lower dowels with some leather to help protect the guitar bodies and to add some friction to the bottom. We have some digital plans available for this multi guitar stand if you want to make your own. I know you can buy cheap guitar racks, but mine can grown with my collection and it is the perfect way to display my favorite instruments. Subscribe: http://bit.ly/ILikeToMakestuffSubscribe Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos Learn 3d modeling, get digital plans, and cool merch at https://iliketomakestuff.com Want to support ILTMS? Get exclusive content and more... http://www.iliketomakestuff.com/patreon FOLLOW: http://instagram.com/iliketomakestuff http://twitter.com/iliketomakestuff http://facebook.com/iltms #ILikeToMakeStuff How to Make a Multi Guitar Stand | I Like To Make Stuff https://www.youtube.com/watch?v=XZ0WRagQ1YM I Like To Make Stuff http://www.youtube.com/Iliketomakestuff

With SocialCounts.org’s view counter, track your YouTube video’s live view count and YouTube likes count in real time with fast, reliable updates.

Watch every YouTube video live view count rise with our real-time YouTube views tracker—built for accuracy and minimal delay.

Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.

Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.org’s smart tracking tools.