Based on this YouTube video's total view count of 3.32M views and industry-standard rates, the estimated total earning is $2.33K - $6.65K through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.

Explore Screen burned Gameboy Pocket restoration and repair with 3,327,716 views, 72,583 likes, and 2,438 comments. Experience the impact of this video content that has captured audience attention.

In this episode I will restore the Gameboy Pocket retro console. This unit is missing the glass screen on top of the actual LCD screen and also the battery cover. I managed to find an original cover. I will show you how to fix a screen burn and do a general cleanup on the Gameboy. I don't do electronical work every week but I promise there will be also this type of videos every once in a while. Check out the link bellow to support this channel. I get a small fee every time you buy from amazon after clicking my links, even if you end up buying something else. --------------------------------------------------------------------- Check out my new Instagram: https://www.instagram.com/odd.tinkering/ Support me on Patreon: https://www.patreon.com/oddtinkering Get My T-shirts from: https://teespring.com/stores/odd-tinkering-2 Tools and materials for this project: Screw driver set: https://amzn.to/2F3n6kO Replacement glass: https://amzn.to/2Hr3oRb Polarizing filter: https://amzn.to/2KSz7Nd Replacement rubber pad for buttons: https://amzn.to/2KS9Dzr Isopropyl alcohol: https://amzn.to/324gED7 Service number sticker: https://ebay.to/2MyIfIR Other stuff you might need: Reproduction shell for gameboy pocket: https://amzn.to/2LbuFbl Battery door with the sticker: https://amzn.to/2KSPAAQ Other sticker for the shell: https://amzn.to/2Hr54Kt The Watch: https://amzn.to/2NpDMJJ --------------------------------------------------------------------- SUBSCRIBE ▶▶▶ https://www.youtube.com/channel/UCf_s... --------------------------------------------------------------------- Restoration playlist▶ https://www.youtube.com/playlist?list=PLVIxIjRNxFv5VRUXt66VzBxOys1GpmBp4 --------------------------------------------------------------------- To open the shell I needed my electronics screw driver set that has the Y-shaped tri-wing screwdriver The shell is closed with that that sort of screws so no one would go tinkering about on the inside. On the inside the screws were normal Phillips heads (cross shape). Board had different looking screws than the metal piece that was attached to the shell so its not easy to mix them up even though I only used one tray. I took also the metal parts out from the shell because I washed it with water but I only show this in my extended Patreon version of the video. I wanted too keep the youtube version much shorter but without cutting out any of the important parts. The board looked fine and I rubber the whatever small corrosion I found off with Isopropyl alcohol. I recommend using electronic grade alcohol like the one I've linked above. The issue with the screen is called screen burn and it is caused by UV-light. The polarizing filter on the screen is damaged. There is another filter behind the screen which can also get damaged but in this case the damage was luckily not so extensive. Sometimes the filter comes off nicely but in my case I know it was going to leave a lot of adhesive residues because of the crystalline look it had. This is not extremely bad but will mean that getting the adhesive off will be much more work. If you are lucky it might only take 10 minutes but for me it took around 1h 45min. When placing the new polarizer it is very important to keep the adhesive on the polarizer clean and also to keep the screen clean because any residue of the old adhesive will leave a nasty looking bubble and if you touch the polarizers glue with your fingers you might end up with sort of foggy looking areas on the screen. I used a piece of tape to help me with aiming the polarizer on it's place. If the polarizer is slightly off it wont matter as the edger will be hidden pretty well. More important part is to make sure you have no bubbles. I had some because it's actually really hard to do this when filming... But luckily I was able to remove them. Thanks for checking out my video once again! If you liked it please subscribe, like and share it with your friends.I don't post these electronic repairs every week, but there will be more so stay tuned!

With SocialCounts.org’s view counter, track your YouTube video’s live view count and YouTube likes count in real time with fast, reliable updates.

Watch every YouTube video live view count rise with our real-time YouTube views tracker—built for accuracy and minimal delay.

Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.

Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.org’s smart tracking tools.