Based on this YouTube video's total view count of 42.8K views and industry-standard rates, the estimated total earning is $30 - $86 through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.

Explore Interior Wall Plastering — Base Coat & Solid Prep! with 42,849 views, 97 likes, and 0 comments. Experience the impact of this video content that has captured audience attention.

TITLE 🏗️ Interior Wall Plastering — Base Coat & Solid Prep! WORKING PRINCIPLE Plastering works in layers: the scratch/base coat bonds directly to porous brick/block, filling gaps and creating a rigid monolithic surface. Sand + cement + water mixed to plastic consistency is thrown/pressed firmly into the brick texture — mechanical key = strong adhesion. This first rough coat provides the structural foundation; it dries into a hard shell that prevents cracking and serves as the base for a smooth finish coat later. Applied thicker where needed to level uneven masonry; left intentionally rough so the next layer bonds perfectly. DESCRIPTION Applying the first scratch coat over interior brickwork — strong bond, full coverage, ready for finishing! EDUCATION - Mix Ratio = Critical: Base coat = 1 part cement : 3–4 parts sand; too rich = shrinks & cracks; too sandy = weak ​ - Pre-Wet Brick: Sprinkle water 15 mins before — dry brick sucks moisture out of plaster → weak bond ​ - Thickness Rule: Single coat = 10–15mm max; thicker = build in 2 layers with 24hr gap ​ - Rough = Good: Don’t smooth base coat — scratch it while still soft → mechanical key for top coat ​ - Working Time: Use within 60–90 mins; never add water to revive — start fresh batch ​ - Curing Matters: Mist lightly 2–3× daily for 3 days — slow water retention = maximum strength ​ - Electrical Points: Embed boxes FIRST — plaster around them; don’t cover then cut out later ​ - Ceiling Gap: Leave 10–15mm space at top — prevents plaster cracking when building settles TOOLS AND MATERIALS Cement, clean sand, water, mixing shovel/bucket, trowel, hawk board, plastering float, brush/spray bottle, straight edge, work gloves, goggles STEPS 1. Dampen wall → protect floor ✅ ​ 2. Mix sand + cement → add water to thick paste ✅ ​ 3. Throw/press firmly onto wall → full coverage ✅ ​ 4. Build up low spots → fill gaps ✅ ​ 5. Level roughly → leave textured/rough surface ✅ ​ 6. Cure → let dry 24–48hrs ✅ ​ 7. Apply finish coat once hard ✅ TIPS - Sift sand first — remove stones → smoother mix, no trowel scratches ​ - Mix small batches — base coat sets fast; waste = cost ​ - Start from bottom → work upward; gravity helps adhesion ​ - Don’t try to level perfectly now — base coat is for strength, not smoothness ​ - If wall is very uneven: dot first → screed → fill between → faster & flatter ​ - Work away from yourself — don’t brush wet plaster ​ - Keep room ventilated but NOT drafty — strong wind dries too fast → cracks ​ - Check bond after drying — tap hollow spots → remove & re-plaster SPECIFICATION - Base Coat Mix: 1 Portland cement : 3–4 clean washed sand; plasticizer optional ​ - Sand Size: 0–4mm coarse/medium grit — fine sand = high shrinkage ​ - Thickness: 10–15mm per coat; 20mm max total before reinforcement ​ - Coverage: ~12–15mm thick = 1 bag cement (50lb) covers ~45–55 sq ft ​ - Drying Time: 24hrs between coats; 7 days full cure ​ - Application Temp: 5–30°C; protect from frost & direct hot sun ​ - Adhesion: Firm hand pressure or spray-on bonding agent recommended ​ - Surface Finish: Scratched/rough texture — no smooth troweling PRICE USA ESTIMATES Portland cement: $11–$18/50lb bag | Plastering sand: $0.05–$0.12/lb or $15–$35/cu ft | Trowel: $18–$42 | Hawk board: $12–$28 | Float: $10–$25 | Mixing tools: $15–$35 | Labor (base coat): $2.50–$5.00/sq ft | Material only: $0.40–$0.80/sq ft ADVANTAGES ✅ Proper base coat = finish never cracks or falls off ✅ Full coverage = seals masonry, blocks dust, strengthens wall ✅ Rough texture = top coat bonds rock-solid ✅ Cement-sand mix = fire-resistant, durable, mold-proof ✅ DIY-friendly technique — just needs practice ✅ Uniform base = less finish material needed later ✅ Prepared walls = faster tiling/painting ✅ Professional prep = professional final result PRODUCTIVITY IMPACT Do the base right and everything after goes smooth — strong foundation = perfect finish! 🏠💪 #PlasteringPro #InteriorRenovation #MasonryFinishing #HomeBuildUSA #SolidWalls   Thank you for watching! Don't forget to like, comment, and subscribe for more great content ✨

With SocialCounts.org’s view counter, track your YouTube video’s live view count and YouTube likes count in real time with fast, reliable updates.

Watch every YouTube video live view count rise with our real-time YouTube views tracker—built for accuracy and minimal delay.

Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.

Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.org’s smart tracking tools.