Based on this YouTube video's total view count of 412K views and industry-standard rates, the estimated total earning is $289 - $826 through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.

Explore Open shelving for your kitchen // How-To | I Like To Make Stuff with 412,852 views, 6,603 likes, and 237 comments. Experience the impact of this video content that has captured audience attention.

A friend wanted some open shelving in her kitchen, so I bought some cheap stair treads and turned them into simple, cheap shelves! CHECK OUT EBATES! http://www.ebates.com/rf.do?referrerid=ehEaMzIc09RJ7uc1xxHRAQ%3D%3D&eeid=26471 Get $10 Gift Card from Target/Walmart/Macy's/Kohl's or $10 Ebates Cash after your first $25 purchase Here are some links to the stores I mentioned... Home and Garden category: http://www.ebates.com/sem2014/landing_page/home-garden_coupons.htm?referrerid=ehEaMzIc09RJ7uc1xxHRAQ%3D%3D&eeid=26471 Home Depot: http://www.ebates.com/coupons/home-depot/index.htm?referrerid=ehEaMzIc09RJ7uc1xxHRAQ%3D%3D&eeid=26471 Lowe’s: http://www.ebates.com/coupons/lowes/index.htm?referrerid=ehEaMzIc09RJ7uc1xxHRAQ%3D%3D&eeid=26471 Target: http://www.ebates.com/coupons/target/index.htm?referrerid=ehEaMzIc09RJ7uc1xxHRAQ%3D%3D&eeid=26471 Walmart: http://www.ebates.com/coupons/walmart/index.htm?referrerid=ehEaMzIc09RJ7uc1xxHRAQ%3D%3D&eeid=26471 HERE'S WHAT YOU'LL NEED: Pine stair treads http://amzn.to/1R7HUoy - Wood glue http://amzn.to/1R7HPRD - Table Saw http://amzn.to/1R7HQVK - Miter Saw http://amzn.to/1jt6ftY - Drill/driver http://amzn.to/1R7HVsz - Level http://amzn.to/1G9Zurk - Bandsaw http://amzn.to/1VOOCGG - Jigsaw http://amzn.to/1VOOEyg - Wall anchors http://amzn.to/1jt6IMN - Rubber mallet http://amzn.to/1VOOIOx - 7" Speed square To get a thickness of 1", I used pine stair treads, but trimmed off the rounded edge. I cut them to length, using the off cuts for the brackets. I drew out a 9" square and a notch for the ledger. From the opposite corner, I used a compass to draw an arch. I cut the brace out on the bandsaw, but a jigsaw would work as well. I cut out the area for the ledger, 3/4" x 2". I used the first brace as a template to trace the others. Then I made a LOT more of them. I used the edge of the belt sander to smooth out my bandsaw cuts. Also, I flattened out the ends of the brace. For the corner shelves, I lined up two panels and made three marks across the joint. Using a biscuit joiner, I cut a biscuit slot on both pieces, at each one of the marks. Both surfaces and all six slots got plenty of glue, and one panel got three biscuits. I clamped the panels together from top and bottom to stock flexing and bowing. After the joints were dry, I sanded the glue squeeze out and all edges. I set the brackets in place, on the TOP side of the shelves, squared them to the edge and traced them. This area is so I know the safe area to drill holes down from the top. I drilled two holes for each brace. The holes were countersunk to allow the screw heads to be flush to the top. I added glue to each brace and held it perpendicular to the shelf. I connected the braces with screws, from the top side. The corner shelves worked the same way, but took a lot longer. All of the holes, and voids were filled with wood filler. Then all of the filler was sanded away and the shelves sanded smooth.   I cut some scrap 3/4" pine into strips, to act as the ledgers. The strips were all chopped to length on the miter saw. Everything was primed and painted with white enamel paint. I marked in 1" (the thickness of the braces) from each end of the ledgers. I predrilled a hole in each one. This hole will be covered by the brace. Every brace has a hole behind it, and the straight shelves have a center hole as well. I held the ledgers in place, leveled them and drilled through the holes to transfer the locations to the wall. I opened up each hole with a larger drill bit, to fit the anchors I'd purchased. The anchors were knocked into the holes. Each of these anchors can support 75lb. Get the correct anchors for your application. I drove screws, through the ledger, into the anchors, and it was really solid. I did the same for the other two ledgers, making sure everything stayed level throughout. The shelves fit tightly onto the ledgers. I used a rubber mallet to knock them into place. I countersunk a hole, through the shelves, into their ledger, followed by a long screw. I predrilled, countersunk and screwed the bottom edge of each brace to the wall for stability. Finally, there was a LOT of hole filling, patching, and touch up painting to do. Since the walls are wavy (old house) I filled gaps with caulking. They turned out really well, and best of all, my friend really likes them! Subscribe: http://bit.ly/ILikeToMakestuffSubscribe Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos Learn 3d modeling, get digital plans, and cool merch at https://iliketomakestuff.com Want to support ILTMS? Get exclusive content and more... http://www.iliketomakestuff.com/patreon FOLLOW: http://instagram.com/iliketomakestuff http://twitter.com/iliketomakestuff http://facebook.com/iltms #ILikeToMakeStuff Open shelving for your kitchen // How-To | I Like To Make Stuff https://www.youtube.com/watch?v=lkTKArJDoc4 I Like To Make Stuff http://www.youtube.com/Iliketomakestuff

With SocialCounts.org’s view counter, track your YouTube video’s live view count and YouTube likes count in real time with fast, reliable updates.

Watch every YouTube video live view count rise with our real-time YouTube views tracker—built for accuracy and minimal delay.

Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.

Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.org’s smart tracking tools.