Based on this YouTube video's total view count of 373K views and industry-standard rates, the estimated total earning is $261 - $746 through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.

Explore Small Pedal Board for Rob Scallon // How-To | I Like To Make Stuff with 373,015 views, 6,618 likes, and 306 comments. Experience the impact of this video content that has captured audience attention.

See how I made a small guitar pedal board for Rob Scallon! Check out Casper at http://casper.com/make Be sure to check out Robs channel https://m.youtube.com/user/robs70986987 Digital plans - http://www.iliketomakestuff.com/product/pedalboard-digital-plan/ TOOLS LIST: https://kit.co/iliketomakestuff/my-woodworking-tools I used some scraps of hardwood that I've been hanging onto for years. Maple for the front and oak for the sides and back. The edges were rough, so I cleaned off one edge of each piece on the table saw. Using that clean edge against the fence, I cut the opposite edge to be parallel. I used a crosscut sled to cut them to length.  This ensures that these cuts are perpendicular to the previous cuts. Then I ripped them all down to the final width. I lined up the pieces in the configuration that I wanted and marked numbers on them so I didn't forget their placement later. I put my dado stack on the saw to make a1/4" cut. Then setup my box joint jig to match the blade size.  I cut box joints on the end of all four pieces. This takes time to setup precisely but the end result is totally worth it. I did a dry fit of the box once all of the fingers were cut. I put a slot cutting bit (the one I used on my arcade) in my router, to create a slot for the aluminum top plate. I cut the slot into each piece being careful NOT to cut into the fingers, just the main section of the board. I cut down a thin aluminum kick plate to size. This material will be used for the top and bottom. The aluminum was thin enough to slide under my fence, so I clamped on a piece of wood that sat completely flush with the table saw surface. Then I cut the piece to it's final width. Before assembly, I sanded the inside of the box pieces, since I wouldn't have access to them again. I added glue to one end piece and the two long pieces before knocking them together with a mallet. I slide the aluminum down into the three slots. I knocked on the final end piece, making sure to adjust the aluminum plate as I went, keeping it in all four slots. I clamped up the box to hold everything in position while it dried. I didn't add a lot of pressure here, just enough to keep everything in place. After it was dry, I used the disc sander to shave off the extra length of the fingers and make them flush. The disc sander has a rough grit paper, and it's very powerful, so it leaves the surface pretty rough. I used a belt sander and orbital sander to get all of the surfaces very smooth. I set the table saw fence to 2" and ran all four sides of the box through the same, cutting it into two pieces. This is tricky and feels dangerous when you do it.  Please be careful. I lined up two off cuts from earlier and marked both pieces for cutting biscuit slots. I used a biscuit jointer to cut the slots, then added glue and biscuits. I clamped these, very tightly, to dry. Subscribe: http://bit.ly/ILikeToMakestuffSubscribe Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos Learn 3d modeling, get digital plans, and cool merch at https://iliketomakestuff.com Want to support ILTMS? Get exclusive content and more... http://www.iliketomakestuff.com/patreon FOLLOW: http://instagram.com/iliketomakestuff http://twitter.com/iliketomakestuff http://facebook.com/iltms #ILikeToMakeStuff About I Like To Make Stuff: We have lots of projects including woodworking, metalworking, electronics, 3D printing, prop making and more! These videos are our attempt inspire and empower others to make the stuff that they want to have. Hopefully you'll see something here that will inspire you to make something that you're passionate about! Small Pedal Board for Rob Scallon // How-To | I Like To Make Stuff https://www.youtube.com/watch?v=qf2lPwmT6WU I Like To Make Stuff http://www.youtube.com/Iliketomakestuff

With SocialCounts.org’s view counter, track your YouTube video’s live view count and YouTube likes count in real time with fast, reliable updates.

Watch every YouTube video live view count rise with our real-time YouTube views tracker—built for accuracy and minimal delay.

Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.

Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.org’s smart tracking tools.