7,396
likes
388
comments
daily view 0
monthly view 0
Live Analytics
Comments 0
Spinning 3D Printer Workstation // How-To | I Like To Make Stuff Analytics Table
Income Estimates for Spinning 3D Printer Workstation // How-To | I Like To Make Stuff
Based on this YouTube video's total view count of 362K views and industry-standard rates, the estimated total earning is $253 - $724 through ad revenue. Historical data is not yet available to calculate daily, weekly, or monthly averages.
About Spinning 3D Printer Workstation // How-To | I Like To Make Stuff
Explore Spinning 3D Printer Workstation // How-To | I Like To Make Stuff with 362,125 views, 7,396 likes, and 388 comments. Experience the impact of this video content that has captured audience attention.
Turning the 3d printer to change the filament is kind of a pain, so I made a way to spin it, and store filament and tools! GET MORE INFO ON THIS PROJECT: http://www.iliketomakestuff.com/make-spinning-3d-printer-workstation HERE'S WHAT YOU'LL NEED: http://amzn.to/1NCVmAb - SawStop cabinet saw http://amzn.to/1GMrfGL - Dewalt 20v drill driver combo http://amzn.to/1HdQuwD - Grizzly G0555LANV Bandsaw http://amzn.to/1GyGjbg - Grizzly Drill Press http://amzn.to/1ntzLSF - Silicone spray http://amzn.to/1ntzEGI - 12" lazy susan bearing http://amzn.to/1WnkyhQ - Pancake compressor/ brad nailer combo http://amzn.to/1LZGfxW - Ultimaker 2 Extended 3D printer I used scrap plywood for this project, so it was a combination of 1/2", 3/4" plywood and MDF. I cut down three pieces to 14 3/4" squares, as this was a little larger than the footprint of my printer. I cut a couple of strips for the side panels. These were a little taller than the diameter of a filament roll. On one of these pieces, I centered a filament roll and traced the inner circle. I made a mark at the far outside of the circle, and drew in a place for a 1/2" dowel hole. I lined the two pieces up and drilled a 1/2" hole through both. I sat the side pieces in place on the base and traced the edge. This shows me the safe area to drill holes. I did the same for the other square piece. On both pieces, I drilled countersunk holes in the safe area. The side pieces got glue on one side before being screwed to the bottom square. I mistakenly glued the top at this point too, but don't do that. Just screw it on. I tested the spacing with a roll of filament hanging on the dowel rod. I cut another scrap that fit within the open side of the box, to act as a drawer front. Two pieces were cut down to act as the sides of the drawer. Their depth was about the depth of the box minus the diameter of the filament roll. I sat the side panel on the side of the box and pivoted it off the bottom front edge. I made a mark on the side panel where I wanted it to hit the box top. Using a straight edge, I drew a line from my mark to the opposite top corner. With both side pieces taped together, I cut along my line on the bandsaw. I trimmed a piece, for the back, down to the same height as the back side of the side panels. Since I was out of plywood scrap, I cut the drawer bottom from MDF. I applied glue to all of the surfaces that would touch. I folded the pieces up into place and used some brad nails to hold everything in place while the glue dried. Using a spacer (scrap), I marked the location for two hinges on the front, bottom edge. I predrilled holes for the hinges, and screwed them in. I held the drawer in place, upside down, to align and screw in the hinges. I flipped the drawer up into place. It was tighter than I wanted, but fit correctly. I sanded down the rough edges and the sides of the drawer where it touched the outer box. I applied some paste wax to the areas that touched which made the drawer move very smoothly! I 3d printed a quick knob (but any knob would work fine). Using a very small bit, I drilled a hole right in the center of the drawer front. I ranĀ a screw in from the back side directly into the back of the knobĀ to hold it in place. I sat the printer in place, centered on the top of the box, and nailed on some small strips along the side of it, keeping them very snug to the printer. On the base panel, I measured a lazy susan bearing, and found the difference in the base's width and the bearings diameter. I split the difference and marked in that distance from each edge. Having these four marks allowed me to easily center the bearing on the base. The two parts of the bearing got lined up so you could see a hole all of the way through. I marked these (4) holes onto the base. Each hole got drilled, with a countersink bit. I centered the bearing the same way on the bottom of the cabinet, but screwed it in place using the four inner holes. The bearing comes un-lubricated, so I sprayed in a little silicone spray and worked it into the bearing. Laying the base on top of the bearing, I aligned the holes using a drill bit and my ice pick. I drove in screws, through the base, into the bearing holes. These are small holes made to be grabbed by sheet metal screws. I flipped the whole thing over and took it for a spin (pun intended). I was able to fit four rolls of filament on the 7/16" dowel. I added all of the 3d printing tools to the drawer and put it in place in my office. Now I can easily spin the machine to swap filaments! Subscribe: http://bit.ly/ILikeToMakestuffSubscribe Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos Learn 3d modeling, get digital plans, and cool merch at https://iliketomakestuff.com Want to support ILTMS? Get exclusive content and more... http://www.iliketomakestuff.com/patreon FOLLOW: http://instagram.com/iliketomakestuff http://twitter.com/iliketomakestuff http://facebook.com/iltms #ILikeToMakeStuff
About YouTube Real-Time View Count
With SocialCounts.orgās view counter, track your YouTube videoās live view count and YouTube likes count in real time with fast, reliable updates.
Watch every YouTube video live view count rise with our real-time YouTube views trackerābuilt for accuracy and minimal delay.
Follow YouTube real time views as they happen, using our dedicated view counter for YouTube videos.
Get up-to-date live view count on YouTube and see real-time growth with SocialCounts.orgās smart tracking tools.
Embed Widget
Parameters:
fullscreen=true- Fullscreen countergraph=true- Live graph chartcounter=0/1/2- Select counter (0=likes, 1=views, 2=comments)
URL
Click to copy the embed URL to your clipboard

